Siemens 1FK7 01. Instructions Manual Download Page 2

Page: 2 / 20

ENGLISH

610.40 700.21

Siemens AG

CONTENTS

General safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Product information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.1

Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.2

Scope of delivery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.1

Rating plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.2

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Transport, Installation and Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1

Transport, Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.1

Important instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.2

Plug design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.3

Motors with DRIVE-CLiQ interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Commissioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

6.1

Checks before starting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

6.2

Commissioning procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Instructions in case of faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Inspection, maintenance, disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Summary of Contents for 1FK7 01.





















Search results

Summary of Contents for 1FK7 01.

Reviews:

Related manuals for 1FK7 01.

Brands by name

Popular brands

Siemens 1FK7 01., Instructions Manual

Search results

Summary of Contents for 1FK7 01.

Reviews:

Related manuals for 1FK7 01.

Brands by name

Popular brands