SICK NAV-LOC Operating Instructions Manual Download Page 58

Page: 58 / 60

NAV-LOC data sheet

8021386/12G4 /2019-04-24 | SICK

OPERATING INSTRUCTIONS | NAV-LOC

Subject to change without notice

NAV-LOC data sheet

12.1

NAV-LOC features

Feature

Value

Application

Localization based on contour data in the indoor area

Supported products

NAV310-3211, NAV340-3232, NAV350-3232, NAV245-10100

SIM2000-0A20A00 Sensor Integration Machine

Communication interface

Ethernet (10/100/1,000 Mbit)
Function: data output

Switching outputs

4, for synchronization

Position resolution

1 mm

Angular resolution

0.001°

Content of output localization
result

Position (X, Y, yaw angle)
Quality information for data fusion and diagnosis of surroundings

Map size

≤ 250,000 m² (per each of the 10 maps)

Max. number of supported
maps/areas

Translational velocity

≤ 2 m/s

Yaw rate (rotational velocity)

≤ 45°/s

Accuracies

2D LiDAR sensor

2D LiDAR sensor

Supported device

NAV310-3211
NAV340-3232
NAV350-3232

NAV245-10100

Aperture angle

360°

270°

Distance Range

10 %: 35m

90 %: 120 m

10 %: 18m
90 %: 50 m

Update rate

Typical 8 Hz

Typical 8.33 Hz

Accuracy

(position measurement)

Typical 30 mm

Typical 35 mm

Accuracy

(yaw angle)

Typical 0.1° ... 0.4°

Repeatability

Typical 4 mm ... 17 mm

Typical 6 mm ... 22 mm

The resolution refers to the output localization result via the result port and can differ from the con-

nected sensor’s measurement resolution.

The resolution refers to the output localization result via the result port and can differ from the con-

nected sensor’s measurement resolution.

1 σ, observe the min. warm-up time of 30 minutes; real value depends on ambient conditions

End position reached, observe the min. warm-up time of 30 minutes; real value depends on ambient

conditions

Summary of Contents for NAV-LOC





























































Search results

Summary of Contents for NAV-LOC

Reviews:

Brands by name

Popular brands

SICK NAV-LOC, Operating Instructions Manual

Search results

Summary of Contents for NAV-LOC

Reviews:

Brands by name

Popular brands