SICK FX3-MOC1 Operating Instructions Manual Download Page 89

Page: 89 / 96

Increase to the response time through the “logic extension” parameter

Table 89: Increase to the response time through the “logic extension” parameter

Check sequence

Expected result

Result OK?

Check that the logic execution
time has been taken into account
when calculating the overall
response time.

The logic execution time has been
checked and taken into account when
calculating the overall response time
with a value of more than 8 ms.

Yes

⃞

17.1.4

Thorough check of the Flexi Soft documentation

Configuration of the safety controller

Table 90: Configuration of the safety controller

Check sequence

Expected result

Result OK?

Check the position ranges and
speed/position profile (in the
MOC1 logic editor).

•

The position ranges entered corre‐
spond to the target application.

•

Only the position ranges in use
have the CAM mark.

•

Position ranges that are not in use
and position 0 do not have the CAM
mark.

Yes

⃞

Thorough check of the response time

Table 91: Thorough check of the response time

Check sequence

Expected result

Result OK?

Check the Flexi Soft CPU cycle
time with the Flexi Soft Designer
software.

•

If the cycle time is > 8 ms, the over‐
all response time for the Safe Lin‐
ear Positioning application must be
recalculated.

•

If the cycle time is 8 ms, the overall
response time provided in this doc‐
ument applies.

Yes

⃞

CPU cycle time value:

Verification of the Flexi Soft configuration

Table 92: Verification of the Flexi Soft configuration

Check sequence

Expected result

Result OK?

Check that the Flexi Soft configu‐
ration has been verified correctly.

•

The tested Flexi Soft configuration
has been verified, which means
that the verification report has
been checked and approved.

•

The CV LED on the CPU lights up
continuously.

Yes

⃞

Documentation of the CRC checksum

Table 93: Documentation of the CRC checksum

Check sequence

Expected result

Result OK?

Check the CRC checksum.

The checksum of the verified Flexi Soft
program has been determined.

Yes

⃞

CRC:

ANNEX

8020941/12O9/2019-08-05 | SICK

O P E R A T I N G I N S T R U C T I O N S | Safe Linear Positioning

Subject to change without notice

Summary of Contents for FX3-MOC1

































































































Search results

Summary of Contents for FX3-MOC1

Reviews:

Brands by name

Popular brands

SICK FX3-MOC1, Operating Instructions Manual

Search results

Summary of Contents for FX3-MOC1

Reviews:

Brands by name

Popular brands