background image

Online Help 

Chapter

 2

Barcode Scanner CLV62x

CLV62x

8011967/S345/2008-04-23

©

 SICK AG ·  Division Auto Ident · Germany · All rights reserved

17

2.2.3.5 Code 93

C

ODE

93 is an alphanumeric code comparable with C

ODE

39 (see 

chapter 2.2.3.2 Code 39, 

page 14

). However, Code 93 requires less space. The same character set (10 numbers, 

26 alphabetic characters and 7 special characters) can be encoded. The code is multiple-
valued (valency 4). 

Fig. 2-7:

Example of Code 93

General

Reading conditions for code type C

ODE

93 are configured via the parameters of the 

General

 

group.

Length

A length test of the barcode can be configured via the parameters of the 

Length

 group.

Parameter

Function

Multireads

Enter the minimum number of required successful readings that 
must be achieved to accept a barcode as valid.

Parameter

Function

Code length mode

Select the type of code-length test.

Interval

Enter minimum length of barcode.
Enter maximum length of barcode.
Only barcodes with lengths between these two values are read.

Fixed lengths

Enter required lengths of barcode. 
Only barcodes with the entered lengths are read.

Summary of Contents for CLV62x









































Reviews: