ELS-7206
Barcode Scanner Quick Guide
Reset Defaults
StartB F3 CodeC 99 99 98 36 End
USB HID
StartB F3 CodeC 31 64 00 26 End
RS232
StartB F3 CodeC 41 55 54 84 End
Configurable Prefix/Suffix
One or two prefix or suffix characters can be added and assigned for data
transmission. Use one of the codes below with a 3 code byte sequence that
represents the desired character (see ASCII Conversion Chart, end of document)
for your prefix or suffix. (To add additional prefix/suffix characters, refer to your
Single-Line Configuration Guide.)
Scan the Enter/Exit Programming bar code to begin. Then scan the 3 digit
decimal equivalent of the ASCII character into the appropriate character location
with the code byte bar codes (see Code Bytes, end of document). To save, scan
the Enter/Exit
Programming bar code again.
Example: To add an asterisk (*) as a prefix,
scan the bar codes:
1. Enter / Exit Programming
2. Prefix 1st Char
3. Code Byte 0
4. Code Byte 4
5. Code Byte 2
6. Enter / Exit Programming
StartB F3 CodeC 99 99 99 41 End
Enter / Exit Programming
StartB F3 CodeC 90 35 00 87 End
Prefix 1st Char
StartB F3 CodeC 90 36 00 91 End
Prefix 2nd Char
StartB F3 CodeC 90 45 00 24 End
Suffix 1st Char
StartB F3 CodeC 90 46 00 28 End
Suffix 2nd Char
Code Byte
StartB F3 CodeC 0 : End
0
StartB F3 CodeC 1 < End
1
StartB F3 CodeC 2 > End
2
StartB F3 CodeC 3 @ End
3
StartB F3 CodeC 4 B End
4
StartB F3 CodeC 5 D End
5
StartB F3 CodeC 6 F End
6
StartB F3 CodeC 7 H End
7
StartB F3 CodeC 8 J End
8
StartB F3 CodeC 9 L End
9
LASER LIGHT. DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
1.0 mW MAX OUTPUT: 650nM
IEC 60825-1:1993+A1+A2
Complies with 21 CFR 1040.10 and 1040.11
except for deviations pursuant to Laser
Notice No. 50, dated June 24, 2007.
LASER RADIATION
Laser Product
This device has been tested in accordance with and complies with IEC60825-1:
1993+A1+A2, EN 60825-1:1994+A1+A2 and 21 CFR 1040.10 and 1040.11,
except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001.
CAUTION-Laser light when open. DO NOT STARE INTO BEAM.
CAUTION - use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous laser light exposure.
Elite Scanner
PN: EDM85696-1 Rev A1125.1
Elite
reserves the right to make changes in specifications and other information
contained in this document without prior notice, and the reader should in all cases
consult
Elite
to determine whether any such changes have been made.
The information in this publication does not represent a commitment on the part
of
Elite
.
Elite
shall not be liable for technical or editorial errors or omissions contained
herein; nor for incidental or consequential damages resulting from the furnishing,
performance, or use of this material.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced,
or translated into another language without the prior written consent of
Elite
.
Copyright 2015 All rights reserved.
Web Address: www.aidcti.com
Disclaimer
