Shuttle FN41 Manual Download

Page: 5 / 74

- 2 -

3.2 JUMPER SETTINGS ................................................................................. 23

JUMPERS & CONNECTORS GUIDE .................................................... 24

Jumpers

Clear CMOS Setting (JP1) ................................................................... 27

Back-Panel Connectors

VGA Port Connectors ............................................................................ 28

COM1 Port Connector ........................................................................... 28

TV-Out Connectors ................................................................................ 28

IEEE 1394 Port Connectors ................................................................... 28

LAN Port Connector ............................................................................... 28

USB1/2 Port Connectors ....................................................................... 28

PS/2 Keyboard & PS/2 Mouse Connectors ............................................ 29

Bass/Center-Out Port Connector ............................................................ 29

Line-Out (Front-Out) Port Connector....................................................... 29

Rear-Out Port Connector ...................................................................... .29

Front-Panel Connectors

ATX Power On/Off Switch Connector (POWER ON) ............................... 30

HDD LED Connector (HDD LED) ........................................................... 30

Green LED / Power LED Connector (GREEN LED/POWER LED) ......... 31

Hardware Reset Connector (RESET)..................................................... 31

Extended USB Headers (JP3/JP11) ...................................................... 32

Front-Panel 1394 Header (JP8) ............................................................. 32

Front Audio Header (JP6) ...................................................................... 33

Internal Peripherals Connectors

Enhanced IDE and Floppy Connector ..................................................... 34

Other Connectors

ATX Power Supply Connector (CN9 and JP13) ...................................... 35

Cooling Fan Connectors for System(FAN1), Chipset (FAN2), CPU (FAN3)

............................................................................................................ 36

Summary of Contents for FN41











































































Search results

Summary of Contents for FN41

Reviews:

Related manuals for FN41

Brands by name

Popular brands

Shuttle FN41, Manual

Search results

Summary of Contents for FN41

Reviews:

Related manuals for FN41

Brands by name

Popular brands