Shuttle FN41 Manual Download

Page: 70 / 74

- 67 -

PC Health Status

CPU Fan AutoGuardian

This SMART Bios enabled 3 phase Variabled Fan Speed and CPU
temperature Control feature.
By default, "CPU Fan AutoGuardian" feature under PC Health Status is
enabled.

The choice: Eabled or Disable.

User Set CPU Fan

This item allows you to choose one specific fan for further setting.

The choice: Fan1, Fan3, or Fan1&Fan3.

Fan Speed Up When CPU Temp

Enabled 3 phase smart control to the Selected fan. This feature ranges
from 40

C to 52

C, in an increment of 4

The choice: 40

C, 44

C, 48

C, or 52

Note:

Before manually modifying the CPU fan setting, please Make

sure both fan connectors are plug into the correct fan
connector designations on the mainboard.

Warning:

It is Strongly recommanded to disable CPU Fan

AutoGuardian feature, if you wish to use other fan cooler,
allowing the fan to run at its default speed.

Summary of Contents for FN41











































































Search results

Summary of Contents for FN41

Reviews:

Related manuals for FN41

Brands by name

Popular brands

Shuttle FN41, Manual

Search results

Summary of Contents for FN41

Reviews:

Related manuals for FN41

Brands by name

Popular brands