Shuttle FN41 Manual Download | Manualshive

Page: 55 / 74

background image

- 52 -

CPU Internal Cache

All processors that can be installed in this mainboard use internal level
1 (L1) cache memory to improve performance. Leave this item at the
default value for better performance.

Ø

The choice: Enabled or Disabled.

External Cache

Most processors that can be installed in this system use external level 2
(L2) cache memory to improve performance. Leave this item at the
default value for better performance.

Ø

The choice: Enabled or Disabled.

Quick Power On Self Test

This item speeds up Power-On Self Test (POST) after you power on the
computer. If it is set to enabled, BIOS will shorten or skip some check
items during POST.

Ø

The choice: Enabled or Disabled.

First/Second/Third Boot Device

The BIOS attempts to load the operating system from the devices in the
sequence selected in these items.

Ø

The Choice: Floppy, LS120, HDD-0, SCSI, CDROM, HDD-1,

HDD-2, HDD-3, ZIP100, USB-FDD, USB-ZIP, USB-CDROM,
USB-HDD, LAN, or Disabled.

Boot Other Device

Select Your Boot Device Priority.

Ø

The choice: Enabled or Disabled.

Swap Floppy Drive

If the system has two floppy drives, you can swap the logical drive
name assignment.

Ø

The choice: Enabled or Disabled.

Boot Up Floppy Seek

Seeks disk drives during boot-Up. Disabling speed boots up.

Ø

The choice: Enabled or Disabled.

Boot Up NumLock Status

Selects power-on state for NumLock.

Ø

The choice: Off or On.

«
...
53
54
55
56
57
...
»

Summary of Contents for FN41











































































Reviews:

No comments

Related manuals for FN41

Brand: Yamaha Pages: 20

BLKDP55WG - P55 LG1156 MAX-16 GB DDR3 ATX Motherboard

Brand: Intel Pages: 88

Brand: Intel Pages: 97

Brand: Global American Pages: 135

Brand: TYAN Pages: 118

Brand: Albatron Pages: 46

Brand: Intel Pages: 29

Brand: QDI Pages: 19

Brand: ECS Pages: 43

Brand: DFI Pages: 183

Brand: TOHATSU Pages: 130

RouterBOARD 500r5 Series

Brand: MikroTik Pages: 14

Brand: ASROCK Pages: 190

Brand: DFI-ITOX Pages: 155

Brand: Intel Pages: 86

Brand: Supero Pages: 95

Brand: Supero Pages: 108

Brand: Supero Pages: 99

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands