Shuttle AN51R User Manual Download Page 72

Page: 72 / 75

- 65 -

Ratio/Voltage Control

CPU Ratio Select

This item allows you to adjust CPU Ratio.

The choice: Auto, X4 800 MHz, X5 1000 MHz, X6 1200 MHz~
X20 4000 MHz.

CPU Voltage Select

This item allows you to adjust CPU Voltage.

The choice: Auto, 0.800V~1.700V.

RAM Voltage Select

This item allows you to adjust RAM Voltage.

The choice: Auto, 2.70 V, 2.80V or 2.90 V.

AGP Voltage Select

This item allows you to adjust AGP Voltage.

The choice: Auto, 1.60 V, 1.70V or 1.80 V.

Chipset Voltage Select

This item allows you to adjust chipset Voltage.

The choice: Auto, 1.70 V,1.80V or 1.90 V.

PC Health Status

The following items provide you with information about the system's
current operating status. You cannot make changes to one of them.

CPU Voltage

AGP Voltage

3.3V VIN

+5V VIN

+12V VIN

-12V VIN

RAM Voltage

5V SBVIN

Voltage Battery

System Temperature

CPU Temperature FAN1 Speed

FAN2 Speed

FAN3 Speed

Summary of Contents for AN51R












































































Search results

Summary of Contents for AN51R

Reviews:

Related manuals for AN51R

Brands by name

Popular brands

Shuttle AN51R, User Manual

Search results

Summary of Contents for AN51R

Reviews:

Related manuals for AN51R

Brands by name

Popular brands