Shuttle AN51R User Manual Download Page 32 | Manualshive

Page: 32 / 75

background image

- 25 -

Jumpers & Connectors Guide

Refer to the mainboard layout on page 12 and this section to help you iden-
tify jumpers, slots, and connectors along with their assigned functions.

CPU/Memory/Expansion Slots

Socket 754 : CPU socket for AMD Athlon

TM

64 , 754-pins processor.

DIMM1/2/3 : Provides three DIMM slots for 64, 128, 256, 512 MB, and
supports up to 3GB capacity max and 1GB per DIMM.

(The total installed memory does not exceed 4GB.)

AGP

: One AGP slot supports up to 8X AGP device.

PCI

: Five 32-bit PCI expansion slots.

B1

E2

E5

E6

B8

B7

E3

E7

E4

E8

E1

E2

E1

D1

D1

E2

A1

E9/E10

E2

E2

D2

D2

A2

A3

B6

«
...
30
31
32
33
34
...
»

Summary of Contents for AN51R












































































Reviews:

No comments

Related manuals for AN51R

Brand: Hailo Pages: 22

Brand: Gan Systems Pages: 24

Brand: Actel Pages: 2

PowerSoC CY3267

Brand: Cypress Pages: 12

Brand: LITETRONICS Pages: 2

Brand: MATSONIC Pages: 76

TPS53355EVM-864

Brand: Texas Instruments Pages: 29

Brand: Advantech Pages: 90

DUOX Programmer

Brand: Fermax Pages: 99

Brand: AXIOMTEK Pages: 67

CONROE1333-ESATA2

Brand: ASROCK Pages: 226

Brand: JETWAY Pages: 52

Brand: Renesas Pages: 17

Supero X9DR3-LN4F+

Brand: Supermicro Pages: 113

Brand: Supermicro Pages: 229

Brand: OMS Pages: 11

Brand: Seco Pages: 49

Brand: Advantech Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands