Shuttle AN50R User Manual Download Page 52 | Manualshive

Page: 52 / 76

background image

- 48 -

4.2.C Install Silicon RAID Driver

Select using your pointing device (e.g. mouse) on the “Install Silicon RAID
Driver "bar to install raid driver.

In

4.2.D Install SiICfg Utility

Select using your pointing device (e.g. mouse) on the “Install SiICfg Utility
" bar to installation Silicfg Utility .

Once you made your se-
lection, a Setup window
run the installation
automatically.
When the copying files
is done, make sure you
reboot the system to
take the installation
effect.

Once you made your se-
lection, a Setup window
run the installation
automatically.
When the copying files
is done, make sure you
reboot the system to
take the installation
effect.

Under Windows 98/ME, if the system doesn't have Serial-ATA harddisk,
please don't install this RAID Utility.

«
...
50
51
52
53
54
...
»

Summary of Contents for AN50R













































































Reviews:

No comments

Related manuals for AN50R

Brand: Texas Instruments Pages: 52

Brand: Aeroflex Pages: 20

Brand: Wintech Pages: 5

Brand: DIEBOLD NIXDORF Pages: 96

Brand: ASROCK Pages: 30

GA-MA785GMT-UD2H

Brand: Gigabyte Pages: 104

KX224-I2C-EVK-001

Brand: Rohm Pages: 3

Brand: OMS Pages: 11

Brand: Commell Pages: 29

Brand: JETWAY Pages: 46

Brand: IDT Pages: 39

WAFER-BW-N4-R10

Brand: IEI Technology Pages: 136

Brand: Ebyte Pages: 9

IN440 Micro-ATX

Brand: trimond Pages: 47

Brand: Texas Instruments Pages: 21

Brand: ON Semiconductor Pages: 2

Brand: Aaeon Pages: 44

Brand: NavSpark Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands