Shuttle AN50R User Manual Download Page 34 | Manualshive

Page: 34 / 76

background image

- 30 -

IEEE 1394 Port Connector

This mainboard offers one 1394 port on
back-panel. Plug device jack into an avail-
able 1394 connector.

10/100 base-T LAN Port
Connector

This mainboard can accommodate one
device on LAN.
Attach a CAT-5 cable to the LAN port at
the back-panel of your computer.

USB Port Connectors

This mainboard offers 4 USB ports on back
panel. Plug each USB device jack into an
available USB1~USB4 connector.

Gigabit LAN Port Connector

This mainboard can accommodate one
device on Gigabit LAN.
Attach a CAT-5 or CAT-6 cable to the LAN
port at the back-panel of your computer.

foxconn

foxconn

1394 Port

USB Port3/4

USB Port1/2

LAN Port

B5

B6

B7

B8

foxconn

foxconn

GigaLAN Port

«
...
32
33
34
35
36
...
»

Summary of Contents for AN50R













































































Reviews:

No comments

Related manuals for AN50R

Intel P43 Series

Brand: J&W Pages: 37

Brand: MSI Pages: 112

K8N Neo3 MS-7135

Brand: MSI Pages: 124

Brand: IBASE Technology Pages: 64

B85M-P32 series

Brand: MSI Pages: 186

Brand: Biostar Pages: 118

Brand: DFI Pages: 44

Brand: TransCore Pages: 40

Brand: TYAN Pages: 100

Brand: Gigabyte Pages: 96

Brand: Aaeon Pages: 44

IRIS-W10 Series

Brand: Ublox Pages: 43

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 105

Desktop Board D850EMD2

Brand: Intel Pages: 24

Brand: Siemens Pages: 15

Brand: Siemens Pages: 26

Brand: Siemens Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands