background image

27

14) Interface

Click to view audio and control data routing for each interface.

15) IP Settings

Displays the network settings for each port:

• Auto: For automatic DHCP or Link-Local IP addresses

• Manual: For Static IP addresses

16) Network Speed

Indicates the speed of the network.

17) Dante Latency

The latency setting for Dante devices should be set according to the 

number of switches in the network. The SCM820 network card has an 

internal switch chip and counts as a switch. For example, one SCM820 

connected to an external switch equals two switches.

See Latency section for more details.

Software

18) Default Language Selection

Determines the language of the GUI when it opens on a computer with 

no prior cookies.

19) Password

By default, no password is required to log on to the GUI. To add an 

Administrator password for the GUI, follow these steps:

1.  Enter password into the New Password field 

2. Repeat for the Password (Confirm)

3. Select Apply to set the password.

Once a password is set, any user can log on as a Guest to view the 

GUI without changing settings.

To clear a password and allow anyone full editing rights:

1. Log on to the GUI

2. Enter the current password into the Old Password text field.

3. Press the Clear button.

20) Load Settings Button

Uploads a file of saved settings to the device. This reconfigures the 

IntelliMix settings of all units in a Link Group.

21) Save Settings Button

Select the Save Settings button to save the mixer settings (configuration 

of the Input, IntelliMix, Output and Preferences tabs). Note: Link Group 

and IP settings are not saved.

22) No Lights Mode

Turns off all visual indicators on the mixer (except the Power LED on the 

front panel).

23) Reset

Returns the mixer to default factory settings (clearing the password and 

device and channel names). The mixer will reboot in Standalone mode.

24) Register This Product

Links to Shure website for product registration.

25) Event Log Link

Links to the device’s Event Log, which opens in a new browser tab or 

window. The log displays a list of all informational system events. 

22

Summary of Contents for IntelliMix SCM820-DAN-DB25





































Reviews: