manualshive.com logo in svg

Shuangri Electron SR258, Operation Manual

Share
Download
Shuangri Electron SR258 Operation Manual Download Page 25

Manual of SR258 intelligent controller 

24 

When the collector temperature exceeds the adjusted collector emergency temperature, 

Then  solar  pump  (R1)  switches  off  in  order  to  protect  the  system  components  against 

overheating (collector emergency shutdown). If the maximum collector temperature (OCEM) 

is exceeded, sign                        is displayed. 

 

           

Warning

! Risk of injury! Risk of system damage by pressure surge! If water is used as 

the heat transfer fluid in pressurized systems, water will boil at 100 °C. Then do not set the 

collector limit temperature higher than 95 °C. 

 

 

OCCO Collector cooling 

The  collector  cooling  function  keeps  the  collector  temperature  rising  within  the  operating 

range by heating the tank. If the tank temperature reaches 95°C the function will be switched 

off for safety reasons. 

 

When the tank temperature exceeds the adjusted maximum temperature of tank, then solar 

system is switched off. If the collector temperature rises up to its adjusted maximum collector 

temperature, the solar pump is switched on again until the collector temperature falls below 

the  maximum  collector  temperature.  The  tank  temperature  may  then  exceed  its  maximum 

temperature, but only up to 95°C (emergency shutdown of the tank), and sign        blinks on 

the screen, system stops.   

If the collector cooling is active,          blinks on the screen.   

 

This  function  is  only  available  when  the  system  cooling  function  (OSYC)  and  the  heat 

transfer function (OHDP) are not activated. 

 

 

OCMI Collector minimum temperature 

The minimum collector temperature is the lowest temperature for running the solar system, 

only when collector temperature is higher than this temperature, solar pump (R1) just can be 

switched-on, if the collector temperature falls below the adjusted minimum temperature, and 

the function will be activated, sign            blinks on the screen slowly.     

 

 

OCFR Collector antifreeze function   

Collector antifreeze function activates the loading circuit between the collector and the tank 

when the collector temperature falls below the adjusted temperature 

CFRO

. This will protect 

the  fluid  against  freezing  or  coagulating.  If  collector  temperature  exceeds  the  switch-off 

Summary of Contents for SR258



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands