Shuang Ri Electron SR288 Operation Manual Download Page 39

Page: 39 / 57

Manual of SR288 intelligent controller

3. Temperature of object tank is lower than its preset maximum temperature.

When the preset temperature difference is exceeded, pump speed control starts. For every

increase or decrease by the rise value, the pump speed will be adjusted by 10 %.



BEEP Beeper fault warning

When system has fault (temperature sensor fault, no flow), beeper sends out warning.

Menu structure

Main
menu

Submenu

Submenu 2

Factory

set

Adjustable
range

Step per
adjust

Description

AUX

Auxiliary functions

SFB

OFF

ON/OFF

Solid fuel boiler function

DTSO

1-50K

0.5K

Switch-on temperature

difference of SFB

DTSF

0.5-49.5K

0.5K

Switch-off temperature

difference of SFB

DTSS

10K

1.5-50K

0.5K

Pump speed control-

temperature difference

RISF

1-20K

Pump speed control- rise

range

MXSS

℃

0.5-95

℃

0.5

℃

Maximum switch-off

temperature of tank

heating

MNSO

℃

0.5-89.5

℃

0.5

℃

Minimum switch-on

temperature of solid fuel

boiler

HEAT

0FF

ON/OFF

Heat transferring between

tanks

Summary of Contents for SR288


























































Search results

Summary of Contents for SR288

Reviews:

Shuang Ri Electron SR288, Operation Manual, Page: 39 / 57

Search results

Summary of Contents for SR288

Reviews: