11
Clearing scenes, chases or group pages
Clearing a entire group, scene or chase page is usefull to get a clean output when programming the
console.
1.
Select the scene, chase or group page you want to clear.
Note:
All three pages from the chase or scene are released with this action so you don’t have to clear
each chase or scene page separately.
2.
Press and hold the
Clear (3.2)
button for 3 seconds.
3.
The LCD will show:
Release all chases
Create a scene
Scenes are simple saved positions, colors etc. which can be recalled by simply pressing a button.
1.
Always release all running functions in order to obtain a clean output.
See chapter 2.2 clearing scenes,
chases or group pages.
2.
Select the fixture(s) you want to use in your scene. (The LED of the selected fixture is lit) by pressing the
desired
fixture buttons (1)
.
3.
Adjust the faders to your liking. (If the fader does not respond, move the fader to zero and try again).
4.
Press the Program button to enter program mode. The LCD will show:
Program mode
.
5.
Select the scene page you wish to store your sene in by pressing the
Scene page 1 (4.2)
,
Scene page 2
(4.2)
or
Scene page 3 (4.2)
button.
The display will show:
Program mode
Scene Page x
(Where x stands for the Scene Page number).
6.
Select a scene you wish to store your settings in by pressing button
1 – 16 (4.4).
The scene will
automatically be stored under the number pressed before.
Note:
A flashing LED in a scene number button indicates it already contains a scene. You can’t
overwrite a scene number which is written. You need to use a scene number which is empty. If you
want to overwrite an excisting page, you have to delete the current scene first (see page 14:
Delete
).
Playing a scene
Before playing a scene, make sure to release manual override by pressing the
Clear (3.2)
button.
1.
Select the scene page you want to use by pressing the
Scene page 1 (4.2)
,
Scene page 2 (4.2)
or
Scene page 3 (4.2)
button.
The display will show:
Play Scene
Scene Page x
(Where x stands for the Scene Page number).
2.
Select a scene you wish to play by pressing button
1 – 16 (4.4).
Note:
Only scenes indicated by a flashing LED contain data ou can’t select an empty scene. The LED
of the selected scene will light up continuously. You can run multiple scenes at the same time by
repeating the instructions above.
Create a chase
There are three ways to create a chase:
A. Create a chase by adjusting the faders.
B. Create scenes first and then select the scenes into the chase.
C. Use a mix of the two ways described above.
Create a chase by adjusting the faders.
1.
Always release all running functions in order to obtain a clean output. See page :
clearing scenes,
chases or group pages.
2.
Press the
Program (3.5)
button to enter programming mode. The LCD will show:
Program mode
.
3.
Select the chase page you want to use by pressing the
Chase page 1 (4.1)
,
Chase page 2 (4.1)
or
Chase page 3 (4.1)
button.
The display will show:
Program mode
Chase Page x
(Where x stands for the Chase Page number.)
4.
Select a chase number you wish to store your settings in by pressing button
1 – 16 (4.4).
Note:
A flashing LED in a chase number button indicates it already contains a chase. You can not
overwrite a chase number which is written. You need to use a scene number which is empty. If you
want to overwrite an excisting chase, you have to delete this chase first (see page 14:
Delete
)
5.
Select the fixture(s) you want to use by pressing the
corresponding
Fixture buttons (1)
.
Summary of Contents for showdesigner 512
Page 1: ...Showdesigner 512 ORDERCODE 50721...
Page 19: ...2011 Dap Audio...
