background image

- 18 - 

 

8.

 

Malfunction Causes and Measures 

Fan malfunction causes and measures 

 

 
 

Malfunction status 

 
 
 
 
 
Malfunction cause 

Overs and sho

rts of quantity 

of wind, the sta

tic pressure

 

Excess/short of motor 

Beari

ng ov

erhe

at/burno

ut 

 

Abnorm

al vibr

a

tion

 

Pecul

iar no

ise

 

Corrosi

on a

nd 

wear

 

Abnorm

al cont

act 

Motor not activated 

Measures 

Defective installation 

 

 

 

 

 

 

 

 Re-installation 

Poor foundation 

 

 

 

 

 

 

 

 

Renovation 

Contact with the rotator? 

 

 

 

 

 

 

 

 

Processing of contact part, 
and re-installation 

Defective duct/duct joint 

 

 

 

 

 

 

 

 Renovation 

Defective lubricating oil 

 

 

      

Replenishment 

Inappropriate oil quality, 
contamination, excessive 
amount of oil 

 

 

      

Replacement 

or 

recycling 

 

Inappropriate material 

 

 

 

 

 

    

Replacement 

Unbalanced impeller 

 

 

 

 

 

 

  

Correction 

Deformation or damage of 
impeller 

 

 

 

     

Repair 

or 

replacement 

Wear or corrosion of impeller 

 

 

 

 

 

 

 

 

Repair or replacement 

Operation at a dangerous speed 

 

 

 

 

 

 

 

 

Renovation or remodeling 
of operation point 

Abnormal bearing of the motor 

 

 

 

 

    

Replacement 

Wrong rotation direction 

 

 

 

 

 

 

 

 Change 

Malfunction of the motor 

 

 

 

 

 

 

 

 

Repair or replacement 

Intake of light gas 

 

 

 

 

 

 

 

 

Renovation/replacement of 
impeller 

Intake of heavy gas 

 

 

 

 

 

 

 

 

Renovation/replacement of 
impeller 

Mixture of foreign object or 
adhesion of scale 

 

 

 

 

 

 

 

 Cleaning 

Surging operation 

 

 

 

 

 

 

 

 

Change of operation point 

Resistance to the pipe system   

 

 

 

 

 

 

 

 

Renovation 

Failure of damper 

 

 

 

 

 

 

 

 Repair 

Accumulation in the drain 

 

 

 

 

 

 

 

 Draining 

There is less pressure loss than 
a plan 

 

 

 

 

 

 

 

 

Damper adjustment, 
change of the rotary speed 

Summary of Contents for MAA1050-Y005E





















Reviews: