background image

- 15 - 

 

 
Rough indication of interval for replenishment of grease 

 

Temperature of 

handled gas 

 

ºC 

Environmental conditions 

Quite clean 

(normal 

environment) 

Much refuse (flour 

mill, sawmill, dust 

collector, etc.) 

Large volume of dust, high 
humidity, or much spray or 

water (refuse disposal 

facility, processed marine 

product factory, etc.) 

50 or less 

6 months 

3 months 

1 month 

50 to 80 

3 months 

2 months 

1 month 

80 to 150 

2 months 

1 month 

1 week 

 

*1  The bearing must not be directly affected by water or refuse. 
*2  If the temperature exceeds 80°C, reduce the interval for replenishment by 1/1.5 each 

time the temperature increases by 10°C. 

 

Rough indication of the replenishment amount of grease 

 

Bearing 

type 

Repleni

shment 

amount 

(g) 

Bearing 

type 

Repleni

shment 

amount 

(g) 

Bearing 

type 

Repleni

shment 

amount 

(g) 

Bearing 

type 

Replenis

hment 

amount 

(g) 

Bearing 

type 

Replenis

hment 

amount 

(g) 

UC203  

204 
205 
206 
207 

1.2 
1.2 
1.3 
2.3 
3.5 

UC208 

209 
210 
211 
212 

4.3
4.9
5.6
8.0
9.8

UC213

214
215
216

12 
15 
16 
19 

UC307

308
309
310
311

5.4 
6.7 
8.4 

12 
17 

UC312 

313 
314 
315 
316 

20 
27 
32 
38 
45 

 

(If a grease gun, which is our standard tool that comes with the product, is used, the 
replenishment amount is approx. 0.5 g each time the lever is operated.) 
 

5.3  Cleaning of a blower and the impeller 

When an ACT type blower is used in a way similar to painting booth and this, please check   
cleaning regularly by all means because an alien substance attaches to a blower part and an   
impeller. In addition, the ACT type blower becomes the structure that internal check is easy to   
make like a figure. 

Open 

Summary of Contents for MAA1050-Y005E





















Reviews: