Shodex R I-50 1 EX Operation Manual Download Page 4

Page: 4 / 36

Thank you for your continued patronage. Observe the following precautions in order

to make safe and stable use of the detector.

Precautions are divided into three groups in this operation manual
depending on the degree of danger. The three groups are

This sign is used where failure to follow strictly the instructions

and procedures indicated by this sign may cause injury or damage

to health.

This sign is used where failure to follow strictly the instructions

and procedures indicated by this sign may cause this detector

and the peripheral apparatus to deteriorate or break down.

This sign is used wherever information is given to ensure optimal

performance of the detector.

Precautions listed below are those of particular importance extracted

from

this operatio

this operation manual :

n manual :

Do not use the detector in places where combustible gas or

any source of fire or of spark exists or might exist.

Prior to connection, make sure that the voltage of the power

socket into which the detector power cable is plugged is the

same as the power supply voltage indicated on the detector.

The type of the power socket into which the detector power

cable is plugged should be of a 3P type with a grounding terminal.

Other type of power socket should not be used.

The accessory power cable should be used to connect the

detector to the power socket. Other cable should not be used.

When using organic solvent, wear safety goggles.

It is recommended that a sink or the equipment for washing eyes

be installed nearby in case the organic solvent in use comes into

contact with the eye(s) or skin.

When any abnormality, such as liquid leakage, is observed,

turn off the power and unplug the detector from the main
power source immediately.

Precautions

Warning

【

Important

】

Caution

Note

Warning

Summary of Contents for R I-50 1 EX





































Search results

Summary of Contents for R I-50 1 EX

Reviews:

Shodex R I-50 1 EX, Operation Manual, Page: 4 / 36

Search results

Summary of Contents for R I-50 1 EX

Reviews: