Shinko Electric CHC-S1245-5 Maintenance Instructions Manual Download Page 31

Page: 31 / 49

YQE8-J0092E

Defective Ejection Pinch Roller

Position sensor, its connector, or cable

disconnection.

Defective DC Motor ASSY (Ejection

Pinch Up/Down), its connector, or

cable disconnection.

Verify that the cable between Ejection Pinch Roller Position

sensor and PCB HSSV7-JUNCTION-F ASSY (CN39-CN84,

CN39-CN85) is properly connected. If it is abnormal,

repairing at manufacturer is required.

Verify that the cable between DC Motor ASSY (Ejection

Pinch Up/Down) and PCB HSSV7-CONT-F ASSY (CN12-

CN59) is properly connected. If it is abnormal, repairing at

manufacturer is required.

Replace DC Motor ASSY (Ejection Pinch Up/Down) 29 and

if it works, DC Motor ASSY (Paper Feed Pinch Up/Down) is

defective.

Defective Paper Feed Cover Open

Switch, its connector, or cable

disconnection.

Verify that the Paper Feed Cover Open Switch is operational.

If it is abnormal, repairing at manufacturer is required.

Verify that the cable between the Paper Feed Cover Open

Switch and PCB HSSV7-JUNCTION-F ASSY (CN48-

CN89) is properly connected. If it is abnormal, repairing at

manufacturer is required.

Dirty Paper Feed Roller of Paper Box.

Use a clear cloth soaked with isopropyl alcohol to clean the

Paper Feed Roller of Paper Box. (Refer to Section 2.6 of

this document)

Defective Thermal Head ASSY, its

connector, or cable disconnection.

Verify that the cable between Thermal Head connector and
PCB HSSV7-CONT-F ASSY (CN3-CN22) is properly
connected. If it is abnormal, repairing at manufacturer is
required.

Replace the Thermal Head ASSY

５

and if it works,

Thermal Head ASSY is defective.

Defective Ambient Temperature

Sensor, its connector, or cable

disconnection.

Verify that the Ambient Temperature Sensor is operational.

If it is abnormal, repairing at manufacturer is required.

Verify that the cable between the Ambient Temperature

Sensor and PCB HSSV7-JUNCTION-F ASSY (CN52-

CN90) is properly connected. If it is abnormal, repairing at

manufacturer is required.

Defective Electromagnetic Clutch , its

connector, or cable

disconnection.

Verify that the cable between Electromagnetic Clutch and

PCB HSSV7-CONT-F ASSY (CN12-CN65) is connected

properly.

Replace Electromagnetic Clutch 11 and if it works, the

original part is defective.

Summary of Contents for CHC-S1245-5


















































Search results

Summary of Contents for CHC-S1245-5

Reviews:

Related manuals for CHC-S1245-5

Brands by name

Popular brands

Shinko Electric CHC-S1245-5, Maintenance Instructions Manual

Search results

Summary of Contents for CHC-S1245-5

Reviews:

Related manuals for CHC-S1245-5

Brands by name

Popular brands