Shinko Electric CHC-S1245-5 Maintenance Instructions Manual Download Page 28

Page: 28 / 49

YQE8-J0092E

Check

Item

Probable Cause

Corrective Action

PCB HSSV7-CONT-F ASSY is

defective.

Replace PCB HSSV7-CONT-F ASSY 1 and if replaced

part works, the original part is defective.

Defective on DC Motor ASSY (Pinch

Roller Up/Down), its connector or

cable disconnection.

Verify that the cable between DC Motor ASSY

（

Pinch Roller

Up/Down

）

and PCB HSSV7-CONT-F ASSY (CN12-CN62)

is properly connected. If it is abnormal, repairing at

manufacturer is required.

Replace DC Motor ASSY

（

Pinch Roller Up/Down

）

８

and

if it works, the original part is defective.

Defective on Pinch Roller Sensor, its

connector, or cable disconnection.

Verify that the cable between Pinch Roller Position Sensor

and PCB HSS7-JUNCTION-F ASSY (CN41-CN71, CN41-

CN72) is properly connected. If it is abnormal, repairing at

manufacturer is required.

If DC Motor (Pinch Roller Up/Down) rotates but error

occurs, Replace Pinch Roller Sensor ASSY 23 .

Connection failure on PCB HSSV7-

JUNCTION-F ASSY.

Verify that the cable between PCB HSSV7-CONT-F ASSY

and PCB HSSV7-JUNCTION-F ASSY (CN4-CN40) is

properly connected. If it is abnormal, repairing at

manufacturer is required.

Defective on DC Motor ASSY

(Thermal Head Up/ Down), its

connector, or cable disconnection.

Verify that the cable DC Motor ASSY (Thermal Head

Up/Down) and PCB HSSV7-CONT-F ASSY (CN12-CN63-

CN68) is properly connected. If it is abnormal, repairing at

manufacturer is required.

Replace DC Motor ASSY (Thermal Head Up/Down)

７

and

if it works, the original part is defective.

Defective on Head Sensor ASSY, its

connector, or cable disconnection.

Verify that the cable between Head Sensor ASSY and PCB

HSSV7-JUNCTION-F ASSY (CN42-CN74, CN42-CN75) is

properly connected. If it is abnormal, repairing at

manufacturer is required.

If DC Motor ASSY (Thermal Head Up/Down) rotates but

error occur, replace Thermal Head Sensor ASSY 22 .

Defective on Electromagnetic Clutch

of Ribbon Brake 2 ASSY, its

connector, or cable disconnection.

Verify that the cable between Electromagnetic Clutch of

Ribbon Brake 2 ASSY and PCB HSSV7-CONT-F ASSY

(CN12-CN66) is connected properly.

Replace Ribbon Brake 2 ASSY12 and if it works, the

original part is defective.

Summary of Contents for CHC-S1245-5


















































Search results

Summary of Contents for CHC-S1245-5

Reviews:

Related manuals for CHC-S1245-5

Brands by name

Popular brands

Shinko Electric CHC-S1245-5, Maintenance Instructions Manual

Search results

Summary of Contents for CHC-S1245-5

Reviews:

Related manuals for CHC-S1245-5

Brands by name

Popular brands