background image

  CAUTION : FIRE

 

 

 Do not carry flammable items (such as fuel, gas and paint) or items that are highly 

combustible near the generator as the muffler, exhaust gas and other parts become 
extremely hot. 

 Position this generator 3 ft. (1 m) or more from walls or other hindrances, and on a 

level surface. 

 Do not connect the generator output to indoor wiring. 

 This generator uses diesel fuel. Always be sure to stop the engine and not bring flames 

close when inspecting fuel or refueling. Wait until the engine has cooled before 
performing such procedures. 

 If fuel spills, always be sure to wipe and drain off spilled fuel. 

 Do not operate the equipment with liquid accumulated in the spill containment. 

 If fuel or oil is leaking, repair the leaking location before operating. 

 Always be sure to wipe up any spilled fuel or oil. 

 Allow the generator to cool before covering with the protective cover. 

 Never allow flame to come close to the generator. 

 Always make sure that the engine is stopped when working on piping. 

 After working on the piping, check that there is no fuel leakage. 

 Absolutely never inspect or perform maintenance to the equipment near fire or other 

open flame. 

 
 

  CAUTION : ELECTRIC SHOCK 

 

 Do not sprinkle water on equipment or used where exposed to rain.

 

 

  CAUTION : BURNS 

 

 Do not touch the engine and surrounding components immediately after stopping the 

engine as they are still extremely hot. 

 Do not open the radiator cap immediately after stopping the engine. Doing so will result 

in hot steam gushing out. 

 Hot steam gushes out from the coolant sub-tank if the generator overheats. Do not 

touch the coolant sub-tank. 

 Always be sure to stop the engine and allow the engine to cool when performing 

inspection or maintenance of engine oil. Opening the oil level gauge or oil filler cap 
during operation will result in hot oil gushing out. 

Summary of Contents for DGA37CM

























































Reviews: