background image

14 

5-4.  Fuel  Line  Changeover  Valve  (3-way  valve) 

 

 

 

 

 

 

 

By switching the 3-way valve, you can use fuel from external fuel tank.   

In this case, the built-in tank fuel cannot be used. 

 

(1)  Using  fuel  from  built-in  fuel  tank 

The lever for 3-way valve is set to 

A

 when the equipment is shipped. 

Outer fuel inlet and return are 

closed with plugs (PT1/2). 

Use fuel as they are. 

 

 

 

 

 

< Note >

 

 

After having used the outer fuel and removed piping, be sure to set the lever to A 

position and fix the plugs. 

 

(2)  Using  fuel  from  external  fuel  tank 

Connect  hoses  from  the  external  fuel  tank  to  the  external  fuel  intake  and  the  external 

fuel return ports, and set the lever for 3-way valve to 

B

 position. 

You can now supply the fuel from   

the external gas tank. 

For detailed instructions, refer to   

9-5.Connecting to External Fuel Tank

   

 

 

 

 

 

 

 

 

 

 

 

 

CAUTION : Fire 

 

 

Always stop the engine when performing any work on the fuel line.

 

 

Always wipe any drip of Diesel fuel or engine oil. Do not use this equipment, 
when a leak is found. Repair the equipment before use. 

 

Be sure to confirm that there is no leakage in the piping. 

 

A side Lever Position

 

3-way valve 

External Fuel Inlet 

 

External Fuel Return (PT1/2)

 

 

B side Lever Position 

3-way valve 

Summary of Contents for DGA37CM

























































Reviews: