background image

TOCV-CP_IMshort_Control-ver-2_Rev07F 

 

Page 14 of 22 

(Software version ≥ 2.00) 

 

effective date: September 2007 

Expected Conc. Range 

Enter the maximum expected concentration. A range value is 
automatically entered based on the selected calibration curve 

No. of Injections 

Enter the minimum/maximum number of injections for the 
samples 

SD Max 
CV Max 

Enter the maximum standard deviation and coefficient of variance 
that is acceptable for the injections. If one of these value is met, no 
additional injections are required. If both values are exceeded, the 
samples are automatically re-injected up to the maximum number 
of injections. 

No. of Washes 

Enter the number of times the syringes is to be washed with 
sample before the first analysis injection 

Auto dilution 

Enter the dilution factor for the samples. The instrument will 
automatically dilute the sample by this factor, and the result will 
be multiplied by the factor to obtain the final concentration. 

Sparge Time 

Enter the required sparge time. This option is available only for 
NPOC analysis. 

Acid Addition 

Enter the percentage of acid to be added to the sample 

Multiple Injections 

If this item is selected, multiple injections are made from a single 
sample aliquot. This larger aliquot is drawn in the syringe in one 
aspiration and is sufficient to  accommodate all of the repeat 
injections 

Use blank check area 

If selected, the blank check value is subtracted from the analysis 
result 

Auto. Correction of inj. 
Vol. and dilution 

If selected the instrument will automatically adjust the injection 
volume and dilution factor and conduct re-analysis when the 
measurement result exceeds the calibration curve range 

  

Method Wizard –5 Peak Time Parameters 

Parameter 

Action/Description 

Analysis 

Displays the selected analysis type 

Use default settings 

If this item is selected, the software default values are used for 
peak detection and the Min. integration time and Max. integration 
items are disabled 

Min. integration time 

Enter the minimum time the instrument signal will continue to be 
detected 

Max. integration  

Enter the maximum time the instrument signal will be detected 
when no peak is found 

 
Note: Wizards from 3 to 5 are displayed for each single analysis type. 
 
Click Finish and the method file is saved 

Summary of Contents for TOC-V CPH























Reviews: