background image

OPERATION Of BL series 2/2 

 

PCS SETTING

 

STEP 

  (1)  Register the PCS unit following the unit registration. 

(Refer to the following.) 

 

  When PCS unit has been already registered, it is not 

necessary to register again. 

  (2)  Place the tare on the pan and press the    TARE    key. 
  (3)  Load the standard sample with required pieces. 
  (4)  Check that the stability mark is lit. 
  (5)  When pressing the  UNIT  key continuously, the 

display will change as follows: 

 

  “

”, “

”,  

 

  “

”, and “

” 

  (6)  Select the desired PCS display and press the    TARE    key. 
  (7)  “      ” is displayed for several seconds and the balance enters the PCS 

unit display.    When the reference sample weight is less than “readability x 
No. of set pieces”, the PCS setting is not made. 

 

  In this case, “           ” is displayed for several seconds and the balance 

returns to weight display. 

% SETTING

 

STEP 

  (1)  Register the % unit. (Refer to the following.) 
 

  When % unit has been already registered, it is not 

necessary to register again. 

  (2)  Place the tare on the pan and press the    TARE    key. 
  (3)  Load the reference sample. 
  (4)  Continuously press the  UNIT  key to display 

               

”. 

  (5)  After the stability mark is lit, press the  TARE  key. 
  (6)  “      ” is displayed for several seconds and the 
 

  balance enters the % unit display. 

Minimum displayed value changes as follows depending on reference 
sample weight (REF.) 
Reference sample weight (REF.) is count value which minimum displayed 
value rearranges one count. 
If the % conversion is not possible, “           ” is displayed for several 
seconds and the balance returns to weight display. 

 

REGISTRATION, CANCEL, AND CHANGE OF UNIT 

 

Step for registration 

  (1)  Press the    CAL/MENU    key and select the 

 display. 

 

  (Press the  TARE  key.) 

  (2)  Press the    CAL/MENU    key and select the 

 display.  

 

  (Press the  TARE  key.) 

  (3)  The registrable unit is displayed by every pressing the    CAL/MENU    key. 

The registerable units are three kinds which are selected from the following 
14 kinds. 

 

  g, kg, ct. pcs, %, oz, ozt, dwt, GN, Hong-kong tail, Singapore tail, Taiwan 

tail, Maraysia tail, and Japanese “monme” 

 

  However, % and pcs (No. of pieces) cannot be registered simultaneously. 

The stability mark is lit on the unit display currently registered. 

  (4)  Press the  TARE  key on the unit display to be registered. That unit is 

registered.When three kinds of unit are already registered, a new registration 

deletes the oldest registration among the three registered units. However, % 
and pcs (No. of pieces) cannot be registered simultaneously. Then deletes 
unnecessary one. 

  (5)  Continuously pressing the    TARE    key returns the display to weight display. 

 

Step for cancel 

  (1)  Carry out the same operation described (1) to (3) above to set unit display. 

Selecting the same one of the unit display which is currently registered 
(stability mark is lit) cancels the registration. 

 

Step for change 

  (1)  Pressing the    UNIT    key changes the unit which is already registered. 
 

  However, even if the unit of % and pcs is already registered, the display does 

not change to this unit unless making a setting of reference value. 

Summary of Contents for BL2200H







































Reviews: