background image

- 7 -

Proportional cycle setting screen (screen No.11) 

Initial value: Contact output   30 seconds 

SSR drive voltage 3 seconds 

Setting range: 1~120 seconds 
Time of proportional setting cycle is set.
The screen does not display voltage or current output. 
Refer to Item 4-6 (4).

Soft start time setting screen (screen No.14)

Initial value: OFF
Setting range: OFF, 1~100%
Time for soft start, during which output is changed gradually, is set. 
Refer to Item 4-6 (6).

Lower limit output limiter setting screen (screen No.12)

Initial value: 0% 
Setting range: 0~99% 
A lower limit value of control output is set.
Refer to Item 4-6 (5) for output limiter.

Communication mode selecting screen (screen No.15)

Initial value: Locl (local)
Setting range: Locl, Remt
Communication is allowed in the mode displayed on the bottom.

Communication address setting screen (screen No.16)

Initial value:  0
Setting range: 0~99
In case a plurality of apparatus are connected for communication, the 
machine No. is set in a range from 0 to 99.

Communication rate selecting screen (screen No.18) 

Initial value: 1200 bps
Selectable range: 1200, 2400, 4800 and 9600 bps
A rate for data transmission to the host is selected.

Delay setting screen Screen No.19
Initial value: 80 
Setting range: 0~255 
Delay time for starting communication from receiving communication 
command is set. 
Delay time = 0.1 

× 

set value msec.

The screen is displayed for RS-485.

Communication data format selection screen (screen No.17)

Initial: 7b_E
Setting range: 7b_E, 8b_n
Select data format of communication from 7b_E (data bit length : 7bits,
parity: even, stop bit : 1)or 8b_n (data bit length: 8bits, parity: none,
stop bit : 1)

Higher limit output limiter setting screen (screen No.13) 

Initial value: 100% 
Setting range: 1~100%
A higher limit value of control output is set. 

Mode 2 Screen Group (Function selecting screen)

NOTE: 

Screen flame on Item 4-4 is as follows:

Screens always shown 
during key operation.

Screens shown or skipped depending on the type of 
output or the setting status of control action mode.

Screens shown during case with 
option or selected option.

1-11

1-12

1-13

1-14

1-15

1-16

1-17

1-18

1-19

Note:

For details of communication, refer to the instructions on 
communication in Item 8. 

V and I 
output 

No 
communi-
cation

RS-422A

2-0

=

=

2-1

Use           key to move select digit and data 
registration, the selectable digit is indicated by 
flashing point.  

ENT

NOTE:

If it is on auto tuning execution or key lock is set on lock No.1,
2 or 3, no selection can be performed even if the digit point is
flashing.

Digits      and      are not shown in case of no option.  Digits of      ,       
and      are not displayed.

     

     :

Measuring range code select digit

Initial value: Multi 05, Voltage (V) 81, Current 95 fixed.
Selecting two digits from “4-5.  Measuring range code table”.

    :

Control output characteristic select digit

Initial value: 

:  RA (heating characteristics)
:  DA (cooling characteristics)

 

Refer to Item 6-3.

    :

Alarm type select digit

Initial value:
Select from “4-2.  Alarm type code table”.

    :

Heater break alarm action mode select digit

 

Initial value:

 

Select from

 

: Lock mode and          : REAL mode.

Refer to Item 5-3 (3).

Input scaling screen

Initial value:
Lower limit value (top row)

0.0

Higher limit value (bottom row) 100.0
Position of decimal point

0.0

Setting range:
Lower limit value -1999~9899 units
Higher limit value -1899~9999 units
Span = Higher limit value - Lower limit value
= 100~5000 counts 
Position of decimal point:
No decimal point, 0.0, 0.00 and 0.000

Scaling is done for linear input (mV, V or mA). 
The screen is only for monitoring and no setting is possible in the case 
of sensor input.
Refer to Item 4-3 (6) for details.

1

2 3

4

5

5

6

3

6

7

1

2

4

5

7

7

8

8

4-5. Measuring range code table

Input type

Code

Code

Measuring

Range

Measuring

Range

*1

*2

*2

B
R

K

K

Pt 100

JPt 100

E
J
T
N
U
L

01

12
13
14
15
16
17
18
19
20
21
22

02
03
04
05
06
07
08
09
10
11
31
32
33
34
35
36
37
38

39
40
41
42
43
44
45
46

71
72
73
81
82
83

95

~

~

~
~

~

~

~

~

~

~

~

~

~

~

~

~

~
~

~

~

~

~
~

~

~

~

~

~

~

~

~

~

~

~

~

~
~

~

~

~

~

~

~

~

~

0

10

0

10

50

100

20

0

0

0

1

5

10

4

V

mA

1800

°

C

1700

°

C

1700

°

C

400

°

C

1200

°

C

700

°

C

600

°

C

200.0

°

C

1300

°

C

200.0

°

C

600

°

C

600

°

C

100.0

°

C

50.0

°

C

200.0

°

C

600

°

C

100.0

°

C

50.0

°

C

200.0

°

C

0
0
0

-100

0
0
0

-199.9

0

-199.9

0

-200

-100.0

-50.0

0.0

-200

-100.0

-50.0

0.0

3300

°

F

3100

°

F

3100

°

F

750

°

F

2200

°

F

1300

°

F

1100

°

F

400

°

F

2300

°

F

400

°

F

1100

°

F

-1100

°

F

200.0

°

F

120.0

°

F

400

°

F

-1100

°

F

200.0

°

F

120.0

°

F

400

°

F

0
0
0

-150

0
0
0

-300

0

-300

0

-300

-150.0

-50.0

0

-300

-150.0

-50.0

0

Thermocouple
B, R, S, K, E, J, T, N: JIS/ANSI/IEC
R. T. D.

Pt100 : Present JIS/IEC
JPt100 : Former JIS

*1 Thermocouple B: Accuracy not 

guaranteed for temperatures 
below 400 

°

C (750 

°

F).

*2 Thermocouple U, L: DIN43710

Multi input

Thermocouple input

R. T. D.

Voltage

Current 

Voltage

mV

Initial value: 0.0~100.0 
Conditions of scaling
Scaling setting range: 
-1999~9999, 
Span: 100~5000 counts 
Position of decimal point: 
No decimal point, the 
first, second and third 
decimal places

In case measuring range is modified, set values, alarm action point and other
related values are all intialized.

NOTE: 

In case types of Alarms are changed, values are initialized.

Summary of Contents for SR73A Series

















Reviews: