manualshive.com logo in svg

Sherman DIGIMIG 225GDS, User Manual, Page: 13 / 27

Share
Download
Sherman DIGIMIG 225GDS User Manual Download Page 13

 

13 

This button is used to select the source control mode. Selecting the appropriate mode is confirmed by lighting of the LED.

Pressing the button for 3 seconds to go to the store mode settings. 

Selecting the operating mode 2T / 4T 

Changing the operating mode between 2T and 4T is possible only in MIG. Mode selection is signaled by lighting up the corresponding LEDs. E Short 
press the switch panel allows the welder to choose the welding mode.

In dwutaktu mode, pressing the switch in the handle grip will enable a wire feeder and arc ignition. Welding is carried out with a finger on the switch. 
Releasing the switch will stop the welding. In czterotaktu mode, pressing the switch in the handle grip will enable a wire feeder and arc ignition. Release 
the switch and lead to the slow welding switch. Pressing the switch will extinguish arc welding and finish.

Loading memory settings. 

Pressing the button for about 3 seconds, the green diode and the transition charging mode settings saved. The display shows the number of the program 
to be loaded. Knob (F), you can change the program number. Pressing the button will load the selected program and switching off the green diode.

F - Knob / control button (hereinafter referred to as wheel) 

Knob (F) adjustment is used to change the welding parameters. Rotate the knob to the left to decrease, and turning to the right to increase the parameter 
value. Simultaneous pressing and turning the knob will quickly change parameter values. Leaving knob motionless for about 8 seconds will save the 
parameter value. Save will be confirmed once the display blink. When you turn off the device and turn it on again automatically reset to the last settings.

Button can be pressed for about 3 seconds on / off mode Spool Gun. Enable or disable the Spool Gun indicated by lighting or extinguishing the LED at 
the display (D)

G - LED HOLD 

The LED HOLD lights up after welding, and the displays (D) for a few seconds displays the last welding parameters. On the left - the welding voltage (V) / 
the right of - the value of the welding current (A)

H - Diodes function VRD / HOT START / ARC FORCE / welding current 

Summary of Contents for DIGIMIG 225GDS




























Reviews:

No comments