manualshive.com logo in svg

shelolab SRI21D, Installation & Operation Manual

Share
Download
shelolab SRI21D Installation & Operation Manual Download Page 30

 

30 | 

P a g e  

OPERATION 

 

 

Continued on next page 

Put the unit in manual night mode (continued)

 

 

 

 

4.

 

Advance to the Event 1 parameter. 

 

a.

 

Press the green 

Advance key

 3 times to reach the 

parameter. 

 

Event 1 Parameter: On

 

 

 

5.

 

Change the parameter to OFF. 

 

a.

 

Press the Up Arrow once. 

 

•

 

This parameter controls the chamber day-illumination 

lights. 

 

 

Event 1 Parameter: Off

 

 

 

6.

 

Save and advance to the Event 2 parameter. 

 

a.

 

Press the Advance key once. 

 

•

 

This simultaneously saves the Event 1 parameter as Off 

while advancing. The small, red 2 indicator will go dark. 

 

 

Event 2 Parameter: On 

 

 

7.

 

Change the Event 2 parameter to Off. 

 

a.

 

Press the Up Arrow once. 

 

•

 

This parameter toggles two outputs to turn off the day 

mode. 

 

 

Event 2 Parameter: Off

 

X3 

Summary of Contents for SRI21D







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands