manualshive.com logo in svg

shelolab SRI21D, Installation & Operation Manual

Share
Download
shelolab SRI21D Installation & Operation Manual Download Page 21

21 | 

P a g e

 

CONTROL PANEL OVERVIEW 

 

 

Power Switch 

The power switch controls all power to the chamber and its systems. Power is supplied when the 

switch is illuminated and in the ( I ) ON position. ( O ) is the OFF position. 

 

Temperature Controller 

The controller arrow buttons are used to adjust the temperature set point, perform calibrations, and 

adjusting the parameter settings of the Day – Night Cycle. 

 

  

 

 

 

 

The EZ1 button is used to launch and terminate the Day - Night Cycle of alternating illumination and 

temperature phases in the cultivation chamber. The EZ2 button does not have a function in the SRI 

chamber. 

The green Advance button is used to scroll forward through Day – Night Cycle pages and to save 

entered time and temperature parameter values. 

The

 

Reset button scrolls the display back to a previous page or menu and also saves currently 

selected parameter values. Pressing the Reset button repeatedly returns the display to the 

Homepage. 

Note: 

On some older controllers, the Reset button may be labeled with an infinity 

∞

 symbol rather 

than RESET. 

Homepage 

Current chamber air 

temperature in red  

Set point in green 

“6” indicates night 

mode 

Figure 3: Control Panel

 

Summary of Contents for SRI21D







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands