Shel lab SCO5W Installation & Operation Manual Download Page 23

Page: 23 / 62

23 |

P a g e

INSTALLATION

CCESS

ORT

TOPPER

Each incubator ships with a rubber stopper installed in the access port located on
the right side the incubation chamber interior.

•

The stopper should always be

installed inside

the chamber

to obtain the

best temperature uniformity and prevent condensation from forming

inside the port.

Do not install the stopper on the outside of the incubator.

•

Wires for thermocouples and other sensor probes may be introduced into

the chamber through the access port. The stopper may be put in place

over the wires.

•

The unit will not meet its temperature or CO

specifications without the

stopper installed.

ILL THE

ATER

ACKET

The water jacket requires

19 gallons (72 liters)

to provide sufficient thermal insulation for the incubator to

operate at its stated temperature specifications.

The manufacturer recommends the use of distilled water or filtered
tap water if possible. Please see the

Anode and Water Quality

entry

in the maintenance section on page 55.

Use of a funnel or hose while filling the jacket is strongly recommended.

Locate the water fill port on the back right side of the

incubator.

Remove the port stopper.

•

Place the port stopper in a location where it will be
easy to find.

Fill the jacket with 19 gallons (72 liters) by pouring water in

through the fill port.

Place the stopper back in the port.

Fill Port

19 Gallons
(72 Liters)

Summary of Contents for SCO5W































































Search results

Summary of Contents for SCO5W

Reviews:

Related manuals for SCO5W

Brands by name

Popular brands

Shel lab SCO5W, Installation & Operation Manual

Search results

Summary of Contents for SCO5W

Reviews:

Related manuals for SCO5W

Brands by name

Popular brands