Shel lab SCO5W Installation & Operation Manual Download Page 34

Page: 34 / 62

P a g e

OPERATION

ET THE

EMPERATURE

OINT

End of Procedure

. Set OTL control to its maximum setting, if not already set to max.

Turning the OTL all the way to the right (clockwise) prevents the heating cutoff

system from interfering with this procedure.

Navigate to the Temperature Set Point Adjustment mode

Push either button

Set Point Adjustment Mode

Note

: The display will automatically exit the adjustment mode after 5 seconds of

inactivity on the arrow keys, saving the last shown set point value.

Set the Temperature Set Point

New Set Point

Adjust

Note

: Adjust the set point to its lowest setting (OFF)

to turn off heating in the chamber.

Wait for 5 seconds after entering the Set Point

Set Temperature

⁰C

The display will stop flashing. The set point is now saved in the controller.

See the

Set the OTL procedure

on page 39 for how to set the OTL system once the

incubation chamber has stabilized at your application temperature set point and

after you have performed any display verifications or calibrations.

HEATING ACTIVATED

Initial Set Point

Set Temperature ⁰C

Summary of Contents for SCO5W































































Search results

Summary of Contents for SCO5W

Reviews:

Related manuals for SCO5W

Brands by name

Popular brands

Shel lab SCO5W, Installation & Operation Manual

Search results

Summary of Contents for SCO5W

Reviews:

Related manuals for SCO5W

Brands by name

Popular brands