Shel lab SCO5W Installation & Operation Manual Download Page 19 | Manualshive

Page: 19 / 62

background image

19 |

P a g e

INSTALLATION

I

NSTALL THE

I

NCUBATOR

Install the unit in a workspace location that meets the criteria discussed in the previous entries of the
Installation section.

D

EIONIZED AND

D

ISTILLED

W

ATER

Do not use deionized water

to clean or humidify the incubator or fill the water jacket. Use of

deionized water may corrode metal surfaces and voids the warranty. The manufacturer recommends
the use of distilled water in the resistance range of 50K Ohm/cm to 1M Ohm/cm, or a conductivity
range of 20.0 uS/cm to 1.0 uS/cm, for cleaning and humidifying and water jacketing applications.

I

NSTALLATION

-

C

LEAN AND

D

ISINFECT

Cleaning and disinfecting the unit incubation chamber, shelving components, and ceiling air duct now
reduces the risk of contamination. The chamber and shelving were cleaned and disinfected at the
factory, however, the unit may have been exposed to contaminants during shipping.

•

Remove all protective wrappings from shelving components and the ceiling air duct prior to

cleaning.

•

Do not clean the chamber HEPA filter

•

See the

Cleaning and Disinfecting

entry on page 43 for information on how to clean and

disinfect without damaging the incubator or its components.

«
...
17
18
19
20
21
...
»

Summary of Contents for SCO5W































































Reviews:

No comments

Related manuals for SCO5W

Brand: E-Mu Pages: 52

Brand: 2easy Pages: 17

Brand: 2DI Pages: 38

Brand: 2DI Pages: 3

Brand: JETBAG Pages: 44

BOS R254K-UUI-LH10-S4

Brand: Balluff Pages: 196

Brand: VEAP SHIELD UNITED Pages: 3

MARTEN-FREE CAR

Brand: Gardigo Pages: 36

Brand: M-S Cash Drawer Pages: 2

Brand: M-S Cash Drawer Pages: 2

Brand: Napoleon Pages: 4

Brand: Quadratec Pages: 8

Brand: QVS Pages: 1

IMI SENSORS EX640B61

Brand: PCB Piezotronics Pages: 70

Brand: LSL Pages: 4

Brand: MSA Pages: 163

Brand: Raw Thrills Pages: 49

Brand: GameSir Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands