background image

33

 

Discount entries 

Your register allows you to deduct a certain amount less than a programmed upper limit after the entry of an 
item or the computation of a subtotal depending on the programming.

Discount for a subtotal

Example

Key operation

Print

60 

z

100 

J

A

Discount for item entries

Example

Key operation

Print

75 

J

A

 

Refund entries

For a refund entry, press the 

F

 key just before you press a department key, 

d

 key, or 

 key or 

just before you scan an EAN code. The operation before pressing the 

F

 key is the same as the one of 

normal operation. For example, if a refund item is the one entered into a department, enter the amount of 

the refund, then press the 

F

 key and the corresponding department key in this order; if an item entered 

into a PLU is returned, enter the corresponding PLU code, then press the 

F

 and 

 keys; and if a 

refund item is the one entered into an EAN, press the 

F

 key and scan the EAN code. 

Example

Key operation

Print

F

 

x

F

 

A

Summary of Contents for XE-A307



















































































































































Reviews: