Sharp XE-A307 Instruction Manual Download Page 88 | Manualshive

Page: 88 / 146

Sharp XE-A307 Instruction Manual Download Page 88

88

■

Manager

You can program a secret code for manager.

Procedure

Program each item as follows:

• PASS CODE (Use the numeric entry)

Pass code (max. 4 digits: 0000 to 9999)

■

Mode Pass Code

You can program a secret code for each mode.

Procedure

Program each item as follows:

The screen continues.

• VOID MODE (Use the numeric entry)

Pass code (max 4 digits: 0000 to 9999)

• OPXZ (Use the numeric entry)

Pass code (max 4 digits: 0000 to 9999)

• FLASH (Use the numeric entry)

Pass code (max 4 digits: 0000 to 9999)

• X1 (Use the numeric entry)

Pass code (max 4 digits: 0000 to 9999)

• Z1 (Use the numeric entry)

Pass code (max 4 digits: 0000 to 9999)

• X2Z2 (Use the numeric entry)

Pass code (max 4 digits: 0000 to 9999)

• PGM (Use the numeric entry)

Pass code (max 4 digits: 0000 to 9999)

• SD CARD (Use the numeric entry)

Pass code (max 4 digits: 0000 to 9999)

«
...
86
87
88
89
90
...
»

Summary of Contents for XE-A307



















































































































































Reviews:

No comments