Sharp XE-A307 Instruction Manual Download Page 44

Page: 44 / 146

Manager Mode

The manager mode is used when managerial decisions must be made concerning register entries, for
example, for overriding limitations and for other various non-programming managerial tasks.

NOTE

Normal register operations may also be performed in this mode.

Entering the Manager Mode

To enter the manager mode, use the following procedure in the REG mode:

Procedure

The secret code entry box will appear.

Manager code

XXXX

Secret code

When “0” is programmed for the secret code

Example

Display

If the code is correct, the register enters the manager
mode.

Override Entries

Programmed limits (such as maximum amounts) for functions can be overridden by placing the register in
the manager mode.

Example

This example presumes that the register has been programmed not to

allow coupon entries over 2.00.

Key operation

Print

250

.......Error

250

NOTE

• When a transaction is finalized, manager is automatically signed off.
• In the initial programming, the HALO function is programmed as "INVALID".

REG-mode entries

Enter to the

manager mode

Summary of Contents for XE-A307



















































































































































Search results

Summary of Contents for XE-A307

Reviews:

Sharp XE-A307, Instruction Manual, Page: 44 / 146

Search results

Summary of Contents for XE-A307

Reviews: