Sharp PG-C45X - Notevision XGA LCD Projector Operation Manual Download Page 91

Page: 91 / 107

Power (OFF) button

Lamp
unit

BQC-XGC50X//1

User service screw

Removing and Install-
ing the Lamp Unit

Info

•

Be sure to remove the lamp unit by the
handle. Be sure not to touch the glass
surface of the lamp unit or the inside of
the projector.

•

To avoid injury to yourself and damage
to the lamp, be sure to carefully follow
the steps below.

•

Do not loosen other screws except for the
lamp unit cover and lamp unit.
(Only the silver screws are loosened).

•

Please refer to the installation manual
included with the lamp unit.

Press

on the projector to

turn off the power.

•

Wait until the cooling fan stops.

Warning!

•

Do not remove the lamp unit from the
projector right after use. The lamp will
be very hot and may cause burn or
injury.

Disconnect the power cord.

•

Unplug the power cord from the AC
socket.

•

Leave the lamp until it has fully cooled
down (about 1 hour).

Change the air filter.

•

Change the air filter whenever you in-
stall the lamp unit (see pages

and

Remove the lamp unit cover.

•

Loosen the user service screw that
secures the lamp unit cover. Then
open the cover in the direction of the
arrow.

AC socket

-86

Regarding the Lamp

Summary of Contents for PG-C45X - Notevision XGA LCD Projector












































































































Search results

Summary of Contents for PG-C45X - Notevision XGA LCD Projector

Reviews:

Related manuals for PG-C45X - Notevision XGA LCD Projector

Brands by name

Popular brands

Sharp PG-C45X - Notevision XGA LCD Projector, Operation Manual

Search results

Summary of Contents for PG-C45X - Notevision XGA LCD Projector

Reviews:

Related manuals for PG-C45X - Notevision XGA LCD Projector

Brands by name

Popular brands