Sharp PG-C45X - Notevision XGA LCD Projector Operation Manual Download Page 86

Page: 86 / 107

Appendix

-81

Replacing the Air Filter

Air filter

Tab

• This projector is equipped with air fil-

ters to ensure the optimal operating
condition of the projector.

• The air filters should be cleaned ev-

ery 100 hours of use. Clean the filters
more often when the projector is used
in a dusty or smoky location.

• Ask your nearest Sharp Authorized

Projector Dealer or Service Center to
exchange the filter (PFILDA005WJZZ)
when it is no longer possible to clean.

Cleaning and replacing
the bottom air filter

Turn off the power and discon-
nect the power cord.

•

Press

. Wait until the cooling fan

stops.

Remove the bottom filter cover.

•

Turn over the projector. Grab the tab
and slide open the filter cover in the
direction of the arrow.

Remove the air filter.

•

Pick the air filter up with your fingers
and lift it out of the filter cover.

Power (OFF) button

Power
(OFF)
button

Air filter

(not removable)

Summary of Contents for PG-C45X - Notevision XGA LCD Projector












































































































Search results

Summary of Contents for PG-C45X - Notevision XGA LCD Projector

Reviews:

Related manuals for PG-C45X - Notevision XGA LCD Projector

Brands by name

Popular brands

Sharp PG-C45X - Notevision XGA LCD Projector, Operation Manual

Search results

Summary of Contents for PG-C45X - Notevision XGA LCD Projector

Reviews:

Related manuals for PG-C45X - Notevision XGA LCD Projector

Brands by name

Popular brands