Sharp FU-28H-S Service Manual Download Page 25

Page: 25 / 36

FU-28H-S

(2) Disconnect the Display PWB and Operation PWB

harnesses from the Control PWB.

Display PWB harness

Operation PWB harness

Display PWB harness

Operation PWB harness

ASSEMBLY PRECAUTIONS

* Make sure the power cord is not pinched when as-

sembling the Front Frame.

* When wiring the power cord, make sure it is not

pinched between the casing plate and the Front
Frame.

3. HOW TO REMOVE THE DISPLAY PWB AND

THE OPERATION PWB

(1) Remove the 2 screws (3 x 12 mm binding head

screws) that are holding the Operation Switch Box
from the Front Frame.

Front

Front Frame

rame

Operation

Operation Switch

witch Box

symbol: 3 x 12 mm screws

Front Frame

Operation Switch Box

symbol: 3 x 12 mm screws

(2) Remove the two screws (3 x 8 mm binding head

screws) and two hooks of the Operation PWB from
the Operation Switch Box, and then separate the
Operation PWB and Operation Button.

Operation PWB

Operation PWB Operation

Operation Switch

witch Box

symbol: 3 x 8 mm screws

Operation PWB Operation Switch Box

symbol: 3 x 8 mm screws

Operation

Operation Button

utton

Operation Button

(3) Remove the 2 screws (3 x 12 mm binding head

screws) holding the Display PWB.

Display PWB

symbol:

symbol: 3 x 12 mm screws

x 12 mm screws

Display PWB

symbol: 3 x 12 mm screws

ASSEMBLY PRECAUTIONS

* Assemble while pulling the Display PWB and Opera-

tion PWB harnesses in the direction of the arrow.

Pull the harness

* Make sure the Display PWB and Operation PWB har-

ness wires do not get pinched.

4. HOW TO REMOVE THE FAN

(1) Remove the 4 intake guard screws (4 x 10 truss

head screws).

symbol: 4 x 10 mm screws

Intake Guard

Cluster Maintenance Cover

symbol: 4 x 10 mm screws

Summary of Contents for FU-28H-S





































Search results

Summary of Contents for FU-28H-S

Reviews:

Related manuals for FU-28H-S

Brands by name

Popular brands

Sharp FU-28H-S, Service Manual

Search results

Summary of Contents for FU-28H-S

Reviews:

Related manuals for FU-28H-S

Brands by name

Popular brands