Sharp FO-A760 Operation Manual Download Page 28

Page: 28 / 69

Sending a Fax: Auto Dialling

Storing a redial number in the
phonebook

Press

, and then

as needed until the number

you wish to store appears.

Press .

Enter a name for the number (see
page 8).

Press .

The number will appear. Press

again to store it.

Automatic redialling

If you use the phonebook or a Rapid
Key to send a fax and the line is busy,
the machine will automatically make
three redial attempts at intervals of five
minutes.

During this time, [

RECALLING

] will

appear in the display, followed by the
attempt number. You will not be able to
dial any other locations while the
message appears.

♦

To clear the message and stop

automatic redialling, press

♦

Under certain conditions, automatic
redialling may stop before three
redialling attempts are made.

Dial Tone Check

This setting determines whether or not
the machine checks for the presence of
a dial on the line before automatic
dialing.

Initial setting: NO

Note:

If you set this setting to YES and

find that the machine is unable to dial,
change the setting to NO.

Press , , ,

and .

Press

(YES) to have the

machine check for a dial tone.

Press

(NO) to have the

machine not check for a dial tone.

Press

exit.

Summary of Contents for FO-A760






































































Search results

Summary of Contents for FO-A760

Reviews:

Brands by name

Popular brands

Sharp FO-A760, Operation Manual

Search results

Summary of Contents for FO-A760

Reviews:

Brands by name

Popular brands