Sharp FO-1460 Service Manual Download Page 27

Page: 27 / 108

SW-D1 No. 1 ~ No. 4 Number of rings for auto receive

When the machine is set in the auto receive mode, the number of
rings before answering can be selected. It may be set from one to
four rings using a binary number. Since the facsimile telephone could
be used as an ordinary telephone if the handset is taken off the hook,
it should be programmed to the user’s choice. If the soft switch was
set to 1, direct connection is made to the facsimile. If a facsimile
calling beep was heard when the handset is taken off the hook, press
the START key and put the handset on the hook to have the facsimile
start receiving. If it was set to 0 accidentally, receive ring is set to 1.

NOTE: If the machine is set to answer after a large number of rings, it

may not be able to receive faxes successfully. If you have
difficulty receiving faxes, reduce the number of rings to a max-
imum of 6.

SW-D1 No. 5 Automatic switching manual to auto receive mode

This soft switch is used to select whether the machine should switch
to the auto receive mode after 5 rings in the manual receive mode or
remain in the same way as SW-D1 No. 1, No. 2, No. 3 and No. 4
"0"1"0"1"(5 rings).

SW-D1 No. 6 ~ No. 8 Reserved

Set to "0".

SW-D2 No. 1 ~ No. 3 Distinctive ringing setting

When the ringing setting is turned off, all of the CI signal are received.
When any of the standard, and ring patterns 1 through 3 is selected
for the ringing setting, only the selected CI signal is received.

CI signal patterns
The CI signal patterns consists of the standard pattern, and ring
patterns 1 through 7. The standard pattern is the conventional one.

SW-D2 No. 4 Reserved

Set to "0".

SW-D2 No. 5 Caller ID function

Used for Caller ID function.

SW-D2 No. 6, No. 7 CI off detection timer (Distinctive ring setting
off only)

Set the minimum time period of CI signal interruption which affords to
be judged as a CI OFF section.

SW-D2 No. 8 High frequency cut when caller ID detecting

If an error occurs when the caller ID is detected by a circuit, set the
switch to "1".

SW-E1 No. 1 ~ No. 8 Reserved

Set to "0".

SW-E2 No. 1 ~ No. 8 Reserved

Set to "0".

SW-F1 No. 1, No. 2 DTMF detect time

Used to set detect time of DTMF (Dual Tone Multi Frequency) used in
remote reception (5

The longer the detect time is, the less the error detection is caused by
noises.

SW-F1 No. 3 Protection of remote

Used to set the function of remote reception (5

). When set to "1",

the remote reception function is disabled.

SW-F1 No. 4 Remote reception with GE telephone

(Corresponding to TEL made by GE) P. B. X.

"1": Compatible with TEL mode by GE

"0": Not compatible

•

When sending (5

) for remote reception with a GE manufac-

tured telephone remote reception may not take place because of
special specifications in their DTMF.
To overcome this, a soft SW is provided to change the modem
setting to allow for remote reception.

•

If this soft SW is set to "1", other telephone sets may be adversely
affected.

SW-F1 No. 5 ~ No. 8 Remote operation code figure by external
TEL (0 ~ 9)

Remote operation codes can be changes from 0 through 9. If set to
greater than 9, it defaults to 9. The "5

" is not changed.

Ex-7

(Default: 5

)

SW-F2 No. 1 CNG detection in STAND-BY mode

When setting to "1", the CNG signal detection function during standby
stops.

SW-F2 No. 2, No. 3 Number of CNG detect (AM mode)

Used for detection of CNG in 1 to 4 pulses.

SW-F2 No. 4, No. 5 Number of CNG (STAND-BY mode)

Used for detection of CNG in 1 to 4 pulses.

SW-F2 No. 6 ~ No. 8 Reserved

Set to "0".

SW-G1 No. 1 ~ No. 4 Quiet detect time

When an answering machine is connected, if a no sound state is
detected for a certain period of time, the machine judges it as a
transmission from a facsimile machine and automatically switches to
the FAX mode.

SW-G1 No. 5 ~ No. 8 Quiet detect start timing

Inserts a pause before commencing quiet detection.

SW-G2 No. 1 ~ No. 8 Reserved

Set to "0".

3.5S

0.5S

RING

PATTERN 1
for CANADA

1.5S

0.8S

0.3S

0.4S