Sharp AR-M160 Manual Download

Page: 137 / 151

AR-M205 FLASH ROM VERSION UP PROCEDURE 12-2

7) PC side:

Double click "Special (MCU/MCU2/FAX)" in the main tree item to

develop the sub tree items, and double click "DWL Download" in the

sub tree items.

8) PC side:

Specify the download file (*.dwl).

9) PC side:

The download file is specified, download is automatically performed.

The "Automatic paper selection" lamp and "Start" lamp will blink

approximately 15 seconds after the download file is specified.

10) PC side:

When the message below is displayed, download is completed.
Completion message: DOWNLOAD COMPLETED

NOTE (Important):

•Be sure that the power is not turned off and the USB cable is not

removed until the word "OFF" appears.

11) Main body side:

Wait until the word "OFF" appears on the operation panel.
The appearance of "OFF" indicates the completion of the download

(writing into ROM).

Turn the power off.

12) After-process: Terminate the maintenance program, and turn on the

power of the main body.

After the download (data transmission) has been completed, exit the
software program. The USB cable can be removed at this point.

NOTE:
•For making a second connection with another machine, select the "File"

and "Reconnect" in the menu bar on the maintenance program at the

time of the USB being re-connected. Repeat the previous procedures
from the above 5).

* Forbidden actions while downloading (Important)

Failure in the download concerned may not allow you to conduct the

subsequent download procedures. Added care should be taken to avoid

having the situation below arise while downloading.
•Switching off the main body of AR-M205/M160.

•Disconnecting the download cable (USB cable).

* If the above inhibit item occurs during downloading:

Turn OFF and ON the power.

1) If "d" (which means downloading) is displayed on the operation

panel LED of the machine, perform downloading again.

2) If "d" (which means downloading) is not displayed on the operation

panel LED of the machine, turn OFF the power, and press and hold

the zoom (%) key and the "Department counter end" key and turn

ON the power. If, then, "d" (which means downloading) is displayed
on the operation panel LED of the machine, perform downloading

again.

If "d" is still not displayed, the MCU must be replaced.

3. Installation procedure

A. USB joint maintenance program installation

The driver is installed by plug and play.

B. Installation procedure on Windows XP

1) Machine

side:

Executable by performing the Service Simulation No. 49-01 (Flash
Rom program-writing mode).

(A word "d" appears on the operation panel to denote the download

mode status. )

2) Connect the machine and the PC with a USB cable.

(Be sure to use a USB cable for connection. USB2.0 of the AR-EB7
is not applicable.)

Summary of Contents for AR-M160
























































































































































Search results

Summary of Contents for AR-M160

Reviews:

Related manuals for AR-M160

Brands by name

Popular brands

Sharp AR-M160, Manual

Search results

Summary of Contents for AR-M160

Reviews:

Related manuals for AR-M160

Brands by name

Popular brands