Sharp AR-M160 Manual Download

Page: 143 / 151

AR-M205 ELECTRICAL SECTION 13-4

The control circuit is subject to negative feedback from the secondary
side as shown in fig (4). A photo coupler (PC002) is employed to insulate

between the primary side and the secondary side to feed back the

control signal to the primary side.
When the output voltage is increased by energy transmission from T001,

the voltage detected by R109 and R111 is compared with the reference

voltage of IC102. When it exceeds the reference voltage, the current
flowing through IC102 (that is, the photo diode current of PC002) is

increased and transmitted to the primary side. Then the potential at the

feedback pin (2 pin) of IC102 is decreased to control Q001. Therefore,
the change in the output voltage on the secondary side is passed

through IC102 and PC002 to control Q001, stabilizing the output voltage.

(4) Overcurrent protection circuit (Primary side)

The inverter circuit of the primary side is connected with the current
detection resistor R012. When an overcurrent occurs in the secondary

side, the current flowing through the primary side inverter Q001 is

increased. The current is detected by R012, and passed through R013 to
IC002 overcurrent restricting pin (3 pin) to turn OFF Q002, shutting off all

power. To resupply the power, turn off and on the power. Refer to fig (4).

(5) Rectifying/smoothing circuit (+5V)

fig (6) Rectifying/smoothing circuit

The high frequency pulse generated by the inverter circuit is decreased
by the converter transformer, rectified by the high frequency diode D103,

and smoothed by C103 and C104.

fig (7) +5V rectifying/smoothing circuit voltage waveform

Summary of Contents for AR-M160
























































































































































Search results

Summary of Contents for AR-M160

Reviews:

Related manuals for AR-M160

Brands by name

Popular brands

Sharp AR-M160, Manual

Search results

Summary of Contents for AR-M160

Reviews:

Related manuals for AR-M160

Brands by name

Popular brands