Sharp AR-BC320 Operation Manual Download Page 9

Page: 9 / 140

0-5

CONTENTS

OPERATION MANUALS.................................................0-1

INSTALLATION REQUIREMENTS.................................0-2

●

Moving this machine..................................................0-3

CAUTIONS......................................................................0-4

CHAPTER 1
BEFORE USING THE PRODUCT

INTRODUCTION.............................................................1-2

MAIN FEATURES ...........................................................1-2

PART NAMES AND FUNCTIONS ..................................1-4

●

Exterior ......................................................................1-4

●

Interior .......................................................................1-5

●

Part names and functions of peripheral devices........1-6

●

Operation panel .........................................................1-8

●

Touch panel...............................................................1-9

AUDITING MODE .........................................................1-11

●

Using the machine when the auditing mode is

enabled ...................................................................1-11

CHAPTER 2
MANAGING THE MACHINE

LOADING PAPER...........................................................2-2

●

Loading paper in paper tray 1....................................2-2

●

Changing the paper size in paper tray 1....................2-2

●

Loading paper in the bypass tray ..............................2-4

●

Loading paper in the stand/1 x 500 sheet paper drawer/

stand/3 x 500 sheet paper drawer .............................2-7

●

Specifications (stand/1 x 500 sheet paper drawer/

stand/3 x 500 sheet paper drawer)............................2-7

●

Loading paper in the duplex module/2 x 500 sheet

paper drawer .............................................................2-8

●

Specifications (duplex module/2 x 500 sheet paper

drawer) ......................................................................2-8

●

Specifications of paper trays .....................................2-9

●

Setting the paper type (except the bypass tray) ......2-11

●

Setting the paper size when an extra size is loaded2-11

●

Setting the paper type and paper size in the bypass
tray...........................................................................2-12

CUSTOM SETTINGS....................................................2-13

●

Operation procedure common to all custom settings
.................................................................................2-13

●

About the settings....................................................2-14

REPLACING THE TONER CARTRIDGES ...................2-15

STORAGE OF SUPPLIES ............................................2-17

MISFEED REMOVAL....................................................2-18

●

Misfeed removal guidance.......................................2-18

●

Misfeed in the paper feed area................................2-19

●

Misfeed in the transport area, fusing area, and exit
area .........................................................................2-20

●

Misfeed in the stand/1 x 500 sheet paper drawer....2-21

●

Misfeed in the stand/3 x 500 sheet paper drawer....2-21

●

Misfeed in the duplex bypass/inverter unit and duplex

module/2 x 500 sheet paper drawer ........................2-22

TROUBLESHOOTING ..................................................2-24

CHAPTER 3
PERIPHERAL DEVICES

SADDLE STITCH FINISHER ......................................... 3-2

●

Part names and functions ......................................... 3-2

●

Specifications............................................................ 3-2

●

Saddle stitch finisher functions ................................. 3-4

●

Using the saddle stitch finisher ................................. 3-6

●

Staple cartridge replacement and staple jam removal .. 3-7

●

Misfeed in the saddle stitch finisher ........................ 3-10

●

Troubleshooting saddle stitch finisher problems..... 3-12

●

Stapling position quick reference guide for duplex

output ...................................................................... 3-13

●

Relation between print image and saddle stitch ..... 3-14

LARGE CAPACITY TRAY............................................ 3-15

●

Part name ............................................................... 3-15

●

Specifications.......................................................... 3-15

●

Loading paper in the large capacity tray ................. 3-16

●

Misfeed in the large capacity tray ........................... 3-17

WhaleII_general-copy_SEC.book 5

ページ

２００４年９月１４日　火曜日　午前１１時４５分

Summary of Contents for AR-BC320













































































































































Search results

Summary of Contents for AR-BC320

Reviews:

Sharp AR-BC320, Operation Manual, Page: 9 / 140

Search results

Summary of Contents for AR-BC320

Reviews: