manualshive.com logo in svg

Sharp AR-BC320, Operation Manual, Page: 129 / 140

Share
Download
Sharp AR-BC320 Operation Manual Download Page 129

TROUBLESHOOTING

7-5

7

Job cancelation
needed

Is a message requesting cancelation of job
displayed?

Press the [CA] (clear all) key to cancel the
current job.

Scanning of
originals is
incomplete.

Is a message indicating memory is full
displayed?

If the data amount exceeds the limit when
using the pamphlet copy or multi shot copy
which requires scanning of all originals,
scanning will be canceled and copying will
not be performed.
If you install an additional memory, the
storage capacity will increase.

The selected
number of sets of
copies is not printed.

For an interrupt copy job, are you attempting
color copying in sort mode?

When color copying is performed in sort
mode for an interrupt copy job, only one set
of copies can be made. If more than one set
is needed, replace the original and repeat
the copy procedure for each set needed.

Not all pages are
copied

When making copies, the memory became
full during scanning of the originals and a
message appears asking you whether you
want to continue copying or cancel.

When the memory becomes full during
scanning of the originals, you can select
whether you want to continue the job and
print only those originals that were scanned,
or cancel the job. If you continue the job,
copies will only be made of the originals that
were scanned, and thus all originals cannot
be copied at once.

Problem

Check

Solution or cause

WhaleII_general-copy_SEC.book  5 

ページ

  

２００４年９月１４日　火曜日　午前１１時４５分

Summary of Contents for AR-BC320













































































































































Reviews:

No comments