Sharp AR-BC320 Operation Manual Download Page 61

Page: 61 / 140

SADDLE STITCH FINISHER

3-13

Stapling position quick reference guide for duplex output

The orientation of the copy paper, original, scanned original data, and binding position selection are all interrelated.
The table below shows these relationships.

Orientation of original or original data

Output result

Page 1

Page 2

Page 1 & Page 2

Duplexed

One-position stapling

Two-position stapling

One-position stapling

Two-position stapling

One-position stapling

Two-position stapling

One-position stapling

Left binding with two-position
stapling is not possible.

Right binding with two-
position stapling is not
possible.

Top binding with two-position
stapling is not possible.

Two-position stapling along
the shorter edge is not
possible.

Right binding

op binding

Left binding

rtrait orientation printing

Landscape orientation printing

WhaleII_general-copy_SEC.book 13

ページ

２００４年９月１４日　火曜日　午前１１時４５分

Summary of Contents for AR-BC320













































































































































Search results

Summary of Contents for AR-BC320

Reviews:

Sharp AR-BC320, Operation Manual, Page: 61 / 140

Search results

Summary of Contents for AR-BC320

Reviews: