manualshive.com logo in svg

Sharp AR-BC320, Operation Manual, Page: 23 / 140

Share
Download
Sharp AR-BC320 Operation Manual Download Page 23

2-1

CHAPTER 2

MANAGING THE MACHINE

This chapter explains how to load paper, replace the toner cartridge,
and remove paper misfeeds. It also contains information about supplies.

Page

LOADING PAPER..........................................................................................2-2

●

Loading paper in paper tray 1 ................................................................2-2

●

Changing the paper size in paper tray 1 ................................................2-2

●

Loading paper in the bypass tray ...........................................................2-4

●

Loading paper in the stand/1 x 500 sheet paper drawer/stand/3 x 500 

sheet paper drawer..................................................................................... 2-7

●

Specifications (stand/1 x 500 sheet paper drawer/stand/3 x 500 

sheet paper drawer) ...............................................................................2-7

●

Loading paper in the duplex module/2 x 500 sheet paper drawer .........2-8

●

Specifications (duplex module/2 x 500 sheet paper drawer) .................2-8

●

Specifications of paper trays ..................................................................2-9

●

Setting the paper type (except the bypass tray)...................................2-11

●

Setting the paper size when an extra size is loaded ............................2-11

●

Setting the paper type and paper size in the bypass tray ....................2-12

CUSTOM SETTINGS ..................................................................................2-13

●

Operation procedure common to all custom settings...........................2-13

●

About the settings ................................................................................2-14

REPLACING THE TONER CARTRIDGES ..................................................2-15

STORAGE OF SUPPLIES ...........................................................................2-17

MISFEED REMOVAL ..................................................................................2-18

●

Misfeed removal guidance ...................................................................2-18

●

Misfeed in the paper feed area ............................................................2-19

●

Misfeed in the transport area, fusing area, and exit area.....................2-20

●

Misfeed in the stand/1 x 500 sheet paper drawer ................................2-21

●

Misfeed in the stand/3 x 500 sheet paper drawer ................................2-21

●

Misfeed in the duplex bypass/inverter unit and duplex module/2 x 500 

sheet paper drawer ..............................................................................2-22

TROUBLESHOOTING .................................................................................2-24

WhaleII_general-copy_SEC.book  1 

ページ

  

２００４年９月１４日　火曜日　午前１１時４５分

Summary of Contents for AR-BC320













































































































































Reviews:

No comments