Sharp AR-405 Operation Manual Download

Page: 62 / 178

3-28

CHAPTER

Place the originals in the document feeder tray or on the
document glass.

Press the 2-SIDED COPY key and select the 1-sided to 2-
sided copy mode.

Press the SPECIAL MODES key.

●

The SPECIAL MODES screen will appear.

Press the “IMAGE EDIT” key on the touch panel.

●

The IMAGE EDIT menu will appear.

Press the “BINDING CHANGE” key on the touch panel.

●

The “BINDING CHANGE” key will be highlighted.

AUTO

READY TO CO

READY TO COPY.

SPECIAL MODES

MARGIN SHIFT

MULTI SHOT

PAMPHLET COPY

ERASE

COVERS

IMAGE EDIT

TEXT STAMP

TRANSPARENCY

INSERTS

DUAL PAGE

COPY

AUTO

EXPOSURE

PAPER SELECT

100%

COPY RATIO

AUTO A4

READY TO COPY.

SPECIAL MODES

IMAGE EDIT

CENTRING

B/W

REVERSE

REPEAT COPY

BINDING

CHANGE

IMAGE EDITING FUNCTIONS

SPECIAL FUNCTIONS

Image editing functions

Summary of Contents for AR-405



















































































































































































Search results

Summary of Contents for AR-405

Reviews:

Related manuals for AR-405

Brands by name

Popular brands

Sharp AR-405, Operation Manual

Search results

Summary of Contents for AR-405

Reviews:

Related manuals for AR-405

Brands by name

Popular brands