Sharp AR-250 Operation Manual Download

Page: 68 / 178

3-34

CHAPTER

ESS

POSITION

CANCEL

Select the desired stamp to be printed.

●

The selected stamp will be highlighted.

Select the pages to be stamped.

●

Indicate whether the stamp is to be printed only on the first page
or on all pages, by pressing the “1ST PAGE ONLY” or “ALL
PAGES” key.

To adjust the exposure and print position, press the
“OPTION” key. Otherwise, proceed to step 10.

●

The following screen will appear.

Adjust the darkness of the background of the stamp.

●

Press the

key to darken or the

key to lighten.

Select the stamp position.

●

The selected position will be highlighted.

●

To return to the previous screen, press the

key.

SELECT STAMP

Confidential

Copy

Draft

Urgent

Preliminary

Final

OPTION

CANCEL

Urgent

Preliminary

Final

1ST PAGE

ONLY

ALL PAGES

CANCEL

Confidential

Copy

Draft

Urgent

Preliminary

Final

OPTION

SELECT STAMP

DARKNESS

CANC

SPECIAL FUNCTIONS

Text stamp

TEXT STAMP

READY TO COPY.

SELECT STAMP

DARKNESS

POSITION

CANCEL

Summary of Contents for AR-250



















































































































































































Search results

Summary of Contents for AR-250

Reviews:

Related manuals for AR-250

Brands by name

Popular brands

Sharp AR-250, Operation Manual

Search results

Summary of Contents for AR-250

Reviews:

Related manuals for AR-250

Brands by name

Popular brands