Sharp AR-250 Operation Manual Download | Manualshive

Page: 114 / 178

background image

7-6

CHAPTER

7

Staple sort

The STAPLE SORT mode staples A4, A4R, B4, and A3 (8-1/2" x 11",
8-1/2" x 11"R, 8-1/2" x 14", and 11" x 17") size copies. Stapled sets
cannot be delivered to the top tray.

NOTE:
Different size originals cannot be copied onto copy paper of their
respective sizes in the STAPLE SORT mode. The paper size selected
for the first scanned original will be used for all originals. To copy
different size originals in the STAPLE SORT mode, select the paper
size for the largest original.

Using the optional SPF/RADF

1

Set the originals in the optional document feeder tray.

●

If the number of copies in one set is more than 50 for
A4 or A4R (8-1/2" x 11" or 8-1/2" x 11"R) paper or 25 for B4 or
A3 (8-1/2" x 14" or 11" x 17") paper, the copies will not be sta-
pled.

●

The stapling positions shown in the left figures are the factory
default positions for the SPF and RADF.

2

Press the OUTPUT key.

3

Press the “STAPLE SORT” key on the touch panel.

Stapling position

OPTIONAL EQUIPMENT

Finisher (AR-FN1N)

FINISHER (AR-FN1N)

AUTO

EXPOSURE

Stapling position

SPF

RADF

READY TO COPY.(DOCUMENT FEEDER MODE)

OUTPUT

TOP TRAY

OFFSET

SORT

OFFSET

TRAY

STAPLE

SORT

GROUP

OK

AUTO

EXPOSURE

PAPER SELECT

100%

COPY RATIO

AUTO A4

«
...
112
113
114
115
116
...
»

Summary of Contents for AR-250



















































































































































































Reviews:

No comments

Related manuals for AR-250

Brand: Gestetner Pages: 168

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands