Sharp AR-250 Operation Manual Download Page 153

Page: 153 / 178

8-7

CHAPTER

Using the key operator programs

Press the CUSTOM SETTINGS (

) key.

Press the “KEY OPERATOR PROGRAMS” key on the
touch panel.

●

The following display will appear.

KEY OPERATOR PROGRAMS

CLEAR

PROGRAM

AUDIT CLEAR

INTERRUPT

KEY OPERATOR PROGRAMS

ENTER KEY OPERATOR CODE.

EXIT

KEY OPERATOR CODE

- - - - -

CUSTOM SETTINGS

AUTO

EXPOSURE

PAPER SELECT

100%

COPY RATIO

AUTO A4

EXIT

DISPLAY
CONTRAST

KEY OPERATOR

PROGRAMS

Enter the key operator code number.

●

The dashes in the display will change to asterisks.

Press the “COPIER” key on the touch panel.

KEY OPERATOR PROGRAMS

EXIT

COPIER

TOTAL COUNT.

PROGRAM LIST
PRINTOUT.

COPIER

PDA/ZR

KEY OPERATOR’S GUIDE

Key operator programs

Summary of Contents for AR-250



















































































































































































Search results

Summary of Contents for AR-250

Reviews:

Brands by name

Popular brands

Sharp AR-250, Operation Manual

Search results

Summary of Contents for AR-250

Reviews:

Brands by name

Popular brands